openmolecules.org

 
Home » DataWarrior » Cheminformatics » Molecular Flexibility Descriptor
Molecular Flexibility Descriptor [message #736] Thu, 19 December 2019 17:24 Go to next message
paulc is currently offline  paulc
Messages: 3
Registered: June 2019
Location: United States
Junior Member

Can anyone elucidate how the molecular flexibility descriptor is defined ?

Much Appreciated,
Paul
Re: Molecular Flexibility Descriptor [message #746 is a reply to message #736] Sun, 29 December 2019 16:28 Go to previous messageGo to next message
thomas is currently offline  thomas
Messages: 344
Registered: June 2014
Senior Member
I will try to give at least a short explanation that summarizes the calculation:

Molecular flexibility values range from 0.0 (rigid) to 1.0 (complately flexible).
Four steps are needed for its calculation:

- All rotatable bonds are determined. These are the only considered contributors to flexibility.
Bending or stretching the molecule or individual bonds is not considered. Double or triple bonds
and bonds within aromatic rings or within 3-, 4- or 5-membered rings are not considered flexible.
All remaining single bonds are considered rotatable, if both atoms are sp2 or sp3 and carry at least
one more non-hydrogen neighbor. For chains of conjugated triple bonds the following applies:
If at least one terminal sp2/sp3 atom has no external neighbor, then no single bond is considered rotatable.
Otherwise that terminal single bond connecting the smaller substituent is considered the only rotatable bond
of the linear atom strand.

- Dihedral angle changes of a bond in the center of a molecule have a much larger effect on the
overall molecule shape that the torsion change of e outer substituent bond. Therefore an influence
factor is calculated for every rotatable bond. It also considers the limited degree of freedom of
ring bond rotation:
- for ring bonds: factor=0.33, since ring bonds cannot be changed without typically affecting two other rings bonds
- other bonds: factor=sqrt(2.0 * smallerSideNonHydrogenAtomCount / moleculeNonHydrogenAtomCount)

- The flexibility contribution of every rotatable bond is determined from statistical torsion data of similar
bonds in the Crystallography Open Database (COD). For instance C-O-C-C (C-O bond) is considered much more flexible
than the central bond in a C-C-C-C chain, which has a strong preference towards the anti-conformation.
For every rotatable bond a characterizing substructure is generated from its local environment.
This substructure consists of the two bond atoms, their direct neighbour atoms and the next shell of neighbour atoms.
It includes all connecting bond orders and various properties, e.g. whether atoms are in a ring, are aromatic,
the stereo configuration, etc. Then canonical representation of the bond's characterizing substructure is built.
The same mechanism was used before to characterize all rotatable bonds of all organic structures of the COD.
Now using the canonical key DataWarrior gets a torsion angle distribution curve of equal bond environments
from all organic structures of the COD. The number of peaks, their heights and their widths are now used to
generate the bond specific flexibility value. Frequency distributions with wide and multiple distribution maxima
of similar heights receive local flexibility values close to 1.0 while histograms with one narrow single
peak are close to 0.0.

- Finally, from the number of all molecule bonds, the number of rotatable bonds, their specific flexibility values,
and their geometry weighting factor an overall flexibility value is calculated with a non-linear incremental approach.

For more details I suggest to check the source code in com.actelion.research.chem.conf.MolecularFlexibilityCalculat or

[Updated on: Sun, 29 December 2019 16:30]

Report message to a moderator

Re: Molecular Flexibility Descriptor [message #755 is a reply to message #746] Tue, 14 January 2020 03:59 Go to previous message
molcreator is currently offline  molcreator
Messages: 1
Registered: January 2020
Location: Xi'an China
Junior Member
Good!
Previous Topic: Molecular Flexibility Descriptor
Next Topic: Automatic Calculation of Properties
Goto Forum:
  


Current Time: Mon Aug 10 08:01:44 CEST 2020

Total time taken to generate the page: 0.00683 seconds